CONNECTING BEHRINGER GEAR TOGETHER WERE THE CABLES GO

[daz/zdz]

CAN ANYBODY DRAW ME A DIAGRAM OF EACH UNIT SHOWING ME HOW THE CABLES ARE CONNECTED TO THE UNITS I HAVE GOT HERE .


MIC

ART/PROFFESIONAL TUBE MIC PREAMP

euro rack ub1204 FX-PRO MIXER

MDX-2600. CHANNEL 1

ultra FEX-PRO-/EX3200

BACK IN TO MDX-2600 CHANNEL 2

Vertuallizer-PRO DSP 2024-P

ICOM -756.
OR SKYPE ME ON M3ZDZ Many thanks VOODOO GUYS

[YO3IBW]

You have "in" and "out" connector, each "out" goes into an "in".
Read the forum and all the essb websites and you will have the answer.

[daz/zdz]

thanks 4 replying 2 me BUT IAM JUST STARTING UP



Mic-pro-caster,in to a art/tub-mic preamp INPUT-XLR come from OUT-XLR OF THE ART-TUB MIC PREAMP INTO-MIC-1 OF THE BEHRINGER EURORACK-UB1204-FX-PRO MIXER FROM THERE TO THE MAIN OUTPUT -XLR [L] SIUTPUTDE OF THE BACK OF THE UB1204-FX-PRO MIXER TO THE MDX-2600 CHANNEL-1 XLR INPUT TO THE EX-3200 OUTPUT XLR TO THEDEQ-2496P INPUT XLR THEN BACK IN TO THE MDX-2600 CHANNEL 2 OUTPUT XLR TO THE DSP -2024P INPUT XLR IN TO A IBOX/W2IHY AUDIO IN 1/4 /TRS JACK THEN AUDIO OUT 5/PIN/DIN IN TO THE FRONT OF THE ICOM -756 8 PIN.


HIS THIS THE RIGTH WAY TO LINK THE CALES TOGETHER.


P.S. I;VE ALSO FIND THAT U CAN ONLY BUY 0.05 LONG XLR CABLES WHY HIS THIS THEY DO NOT MAKE THEM ANY SHORTER. ANY WAY I WILL MAKE MY OWN SO THEY ARE THE RIGTH LENGHT. TO MAKE MY LEADS CAN I USE 2 COR WITH A GOOD SHEID I NO ON 1 SITE IT SAY 4 COR AND SHEID BUT U ONLY U 2 WIRES ANY AND SHEID.THEY ARE ALL WIRE BALANCED MANY THANKS 4 ALL YUR HELP VOODOO GUYS. DAZ. M3ZDZ

[Voodoo Guru]

Howdy Daz/zdz,

That was a good try, but you might have problems with that connection setup.

Its best to start simple then try the different connection schemes later when you are more familiar with them.

This should get you started.......


Mic-pro-caster to the ART-mic preamp Input XLR

ART Mic Preamp Output XLR to the DEQ2496 Channel 1 Input XLR

DEQ2496 Channel 1 Output XLR to the EX3200 Channel 1 Input XLR

EX3200 Channel 1 Output XLR to the MDX2600 Channel 1 Input XLR

MDX2600 Channel 1 Output XLR to the DSP2024P Channel 1 Input XLR

DSP2024P Channel 1 Output XLR to the IBox

IBox to the ICOM-756


You do not need the UB1204 mixer at this time.

Yes the cable lengths are usually pretty long when you purchase them pre-made. Thats why most people will make there own, its also cheaper.

The 4 conductor Star Quad type cable is much more resistant to RFI and 60cps Hum. It also has superior braided shielding, and is more durable.

Good Luck!

[M0AOV]

thanks 4 replying 2 me BUT IAM JUST STARTING UP



Mic-pro-caster,in to a art/tub-mic preamp INPUT-XLR come from OUT-XLR OF THE ART-TUB MIC PREAMP INTO-MIC-1 OF THE BEHRINGER EURORACK-UB1204-FX-PRO MIXER FROM THERE TO THE MAIN OUTPUT -XLR [L] SIUTPUTDE OF THE BACK OF THE UB1204-FX-PRO MIXER TO THE MDX-2600 CHANNEL-1 XLR INPUT TO THE EX-3200 OUTPUT XLR TO THEDEQ-2496P INPUT XLR THEN BACK IN TO THE MDX-2600 CHANNEL 2 OUTPUT XLR TO THE DSP -2024P INPUT XLR IN TO A IBOX/W2IHY AUDIO IN 1/4 /TRS JACK THEN AUDIO OUT 5/PIN/DIN IN TO THE FRONT OF THE ICOM -756 8 PIN.


HIS THIS THE RIGTH WAY TO LINK THE CALES TOGETHER.


P.S. I;VE ALSO FIND THAT U CAN ONLY BUY 0.05 LONG XLR CABLES WHY HIS THIS THEY DO NOT MAKE THEM ANY SHORTER. ANY WAY I WILL MAKE MY OWN SO THEY ARE THE RIGTH LENGHT. TO MAKE MY LEADS CAN I USE 2 COR WITH A GOOD SHEID I NO ON 1 SITE IT SAY 4 COR AND SHEID BUT U ONLY U 2 WIRES ANY AND SHEID.THEY ARE ALL WIRE BALANCED MANY THANKS 4 ALL YUR HELP VOODOO GUYS. DAZ. M3ZDZ

If your looking for shorter cables i.e. 0.03 Long look here http://cgi.ebay.co.uk/ws/eBayISAPI.dll? ... 662wt_1139

Rob